Plan whole-house air conditioning in North London: room-by-room sizing, multi-split and ducted options, zoning, outdoor units, drainage and permissions.
Begin with the rooms, not the equipment
Decide which spaces genuinely need cooling and heating. Bedrooms may need low-noise overnight operation, while a south-facing kitchen and living area can have stronger solar and appliance gains. A home office may be occupied all day, but a spare bedroom may only need occasional use. Treating every room identically can increase cost and compromise comfort.
A room-by-room heat-load assessment should consider dimensions, ceiling height, glazing, orientation, shading, insulation, occupancy and heat-producing equipment. Generic square-metre charts are only a starting point. Read our North London home air-conditioning guide for the main survey questions.
Choose the system layout around the property
A single-split system connects one indoor unit to one outdoor unit. It gives a priority room independent control and can be a sensible first phase. Installing several unrelated single splits may be straightforward technically, but it needs enough discreet outdoor space and creates more external equipment.
A multi-split connects several indoor units to one condenser. It can reduce the number of outdoor units, which is valuable on tighter North London plots, but pipework design is more involved and connected rooms share one outdoor system. A failure or maintenance visit can therefore affect several rooms. Our single-split versus multi-split guide compares these options in more detail.
When ducted air conditioning is worth considering
A ducted system hides the main indoor unit above a ceiling, in a loft or within suitable joinery, with air supplied through grilles. It can give a restrained finish and serve several nearby rooms, but it needs adequate void space, correctly sized ducts, return-air paths and access for filters and servicing.
Ducting should not be squeezed into whatever space remains after building work. Poor routes, undersized grilles or insufficient return air can create noise and restrict performance. Ducted systems are easiest to coordinate during a major refurbishment, loft project or new extension. Existing homes with limited voids often suit carefully positioned high-wall units better.
Zoning matters for comfort and running time
Whole-house does not have to mean every room operates together. Bedrooms, living spaces and offices have different schedules, so the design should allow occupied zones to run without conditioning unused rooms. With multi-splits, confirm the combination of indoor units, available capacity and operating limits against the manufacturer’s design data.
Do not expect one hallway unit to cool closed bedrooms. Air follows the available path, and closed doors prevent dependable room control. Individual indoor units or properly designed duct branches provide more predictable results.
Plan indoor positions before decorating
Every indoor unit needs clear return airflow and a route that distributes air without blowing directly onto beds, desks or sofas. Check wardrobes, curtains, tall furniture, door swings and planned joinery. Future filter access matters too; an attractive position is not successful if routine maintenance requires dismantling the room.
Pipework and cable containment can often be kept neat when routes are agreed early. Our indoor and outdoor unit positioning guide covers clearances, airflow and service access.
Outdoor-unit space can decide the whole design
Before selecting a multi-room system, identify stable outdoor positions with suitable airflow and access. Consider bedroom windows, neighbouring homes, boundaries, seating areas and the appearance from the street. Manufacturer clearances must be maintained; a decorative screen must not trap discharge air.
More indoor rooms do not automatically mean an unlimited number of units can connect to one condenser. The proposed combination, total pipe length, height differences and capacity range must all be checked. On larger properties, two sensibly grouped systems may offer better routing and resilience than forcing every room onto one outdoor unit.
Resolve drainage and electrical supply early
Each indoor unit produces condensate during cooling. Gravity drainage is generally the simplest approach where a continuous fall reaches a suitable discharge point. Pumps can solve difficult routes, but their sound, cleaning and replacement access should be understood before installation.
The electrical design depends on the selected equipment and existing installation. Dedicated circuits, isolation and cable routes should be confirmed rather than assumed. Approved Document P covers electrical safety in dwellings in England, including design, installation, inspection, testing and information requirements.
Check planning and property permissions
Planning Portal guidance says an air-source heat pump at a house or block of flats can be permitted development only when every relevant limit and condition is met. Current conditions address matters including the applicable planning standard, number and size of outdoor units, roof and highway-facing positions, listed buildings, conservation settings, appearance and local amenity. The equipment must not be used solely for cooling.
Whole-house designs may involve more than one outdoor unit, so check the proposed layout rather than assuming the first-unit rules cover the complete scheme. Leasehold properties also require an early check of the lease and any freeholder or managing-agent consent. Where the position is sensitive or uncertain, ask the local planning authority before work starts. See our North London planning guide.
Use appropriately qualified installers
Most fixed split systems contain fluorinated refrigerant. GOV.UK states that individuals need the correct qualifications for work including installation, servicing, maintenance, leak checking, recovery and decommissioning. It also requires approved company certification for businesses, including sole traders, carrying out relevant work on stationary equipment for others.
Official guidance checked 15 October 2026: Planning Portal air-source heat-pump conditions, GOV.UK Approved Document P, and GOV.UK guidance on individual and company F-gas certification.
Frequently asked questions
Can one outdoor unit air-condition the whole house?
Sometimes, if a compatible multi-split or ducted arrangement covers the required rooms within the manufacturer’s capacity and pipework limits. Larger or awkward properties may work better with two grouped systems.
Is ducted air conditioning better than wall units?
Neither is automatically better. Ducted systems offer discreet grilles but need suitable voids and carefully designed airflow. High-wall units usually need less building work and give straightforward room control.
Can I install the upstairs first?
Yes. A phased design can prioritise bedrooms and allow later living-space additions, provided outdoor positions, electrical capacity and future routes are considered at the start.
Will air conditioning heat the whole house too?
Reversible systems can provide heating, but the winter heat load and manufacturer performance data must be checked for every proposed zone. Read our guide to heating your home with air conditioning.
Planning a whole-house system?
An owner-led survey can map the rooms, heat loads, indoor and outdoor positions, pipe routes, drainage and electrical requirements before equipment is selected.
Request a whole-house survey →Explore domestic air-conditioning or view coverage in Muswell Hill, Highgate, Crouch End, Hadley Wood and across North London.
Before you request a quotation
Collect the room dimensions, note when the space overheats, take photos of possible indoor and outdoor positions and confirm whether the property is freehold or leasehold. This gives the designer a useful starting point, but it does not replace a heat-load assessment or site survey.